Before You Order a Container: 10 Things to Test on Your Electric Scooter Sample
A sample is your cheapest insurance. Ten checks — range, battery, charger, brakes and paperwork — to run before you commit to a container.

A sample is your cheapest insurance
A sample costs far less than a container of the wrong vehicle. Its job is not to impress you on a showroom floor. Its job is to answer, on your roads and with your load, whether the production vehicles will do what the brochure promises.
Run these ten checks before you commit — and record the results with photos and video, so the factory and your customers can see the same evidence you did.
That last point — recording the evidence — is what turns a sample ride into a buying decision you can defend. Memory fades, and two people who rode the same scooter on the same day can remember it quite differently. A dated test sheet, with the load used, the route ridden, the distance covered, the charge level at the start and finish, and photos of anything that looked wrong, gives you something firmer. It lets you compare the sample against the specification in writing, show the factory exactly what you found, and later compare the production vehicles against the sample you approved. If a dispute ever arises about what was promised, that record is worth more than any recollection of a phone call.
Plan the test before the sample arrives, not after. Decide who will ride it, which routes represent your real customers, what load you will carry, and what result would count as a pass, a fail, or a point to negotiate. Tell the factory your test conditions in advance and confirm the sample configuration in writing — model, motor, battery voltage and capacity, battery chemistry, charger, and tyres — so that you are testing the vehicle you would actually order, not a stronger or different version prepared for display. If the sample arrives in a different configuration from the one confirmed, stop and raise it straight away. Testing the wrong configuration is worse than not testing at all, because it creates confidence you have not earned.
Also give the sample enough use to reveal ordinary problems, not just first impressions. A short ride around the block will show you the colour and the seat height. It will not show you whether the charger runs hot, whether a fastener loosens, whether the range holds up with a passenger, or whether a switch becomes annoying on the twentieth use. Where you can, put the sample into something close to real daily service for several days: your own commute, a delivery rider's shift, or repeated runs over your typical route. The problems that cost dealers money are rarely dramatic failures. They are small, repeated irritations — and only repeated use finds them.
The 10 checks
- Real range, on your roads. Ride the sample on your usual routes, with your usual load. Do the battery maths first: capacity (Wh) = voltage (V) × capacity (Ah). Compare the result with the claimed range, and record what you actually got. To make this test fair and repeatable, start from a full charge, note the odometer or trip reading, ride a known route at your normal pace with your normal load, and record the distance covered and the charge remaining at the end. Repeat the run if you can, because traffic, wind, hills, and riding style all move the result. The decision you are making is not whether the sample matched a brochure number in perfect conditions, but whether the range you measured, on your roads, leaves your customers a comfortable margin for a full day's use. A common mistake is to test alone, unloaded, on flat ground, and then sell the vehicle to customers who ride two-up on hills — the gap between those two tests becomes your complaint rate.
- Battery identity. Check the battery voltage, capacity and chemistry against your order, and confirm the pack is the one on the specification sheet — including the connector and whether it is removable, if that matters to your customers. Photograph the battery label and keep that photo with your test record. If the battery is removable on your configuration, remove it and refit it yourself, several times, the way a customer would: check the weight in your own hands, the fit of the connector, and whether anything feels fragile or awkward. If it is not removable, confirm how charging works in practice for a customer without a ground-floor socket. The mistake to avoid is assuming the sample battery is the production battery. Ask the factory to confirm in writing that the production vehicles will carry the same voltage, capacity, and chemistry you just tested.
- Charging, start to finish. Charge with the supplied charger from low to full. Confirm the plug fits your market, the voltage matches, and the charging time is close to the stated figure — on the Lubon LB-CS the listed charging time is 4–6 hours; confirm it for your exact configuration. Time the charge yourself rather than estimating it, note the charge level you started from, and check the charger and battery part-way through for unusual heat, noise, or smell. Test the socket and plug your customers will actually use, not an adaptor you happen to have in the office. Ask yourself practical questions while you wait: is the cable long enough for a typical parking spot, is the charge indicator easy to read, and does the charger clearly show when charging is complete? A sample that charges correctly but awkwardly will generate daily complaints that no specification sheet predicts.
- Motor behaviour under load. Ride with your typical load — a passenger, or a loaded delivery box — on your steepest regular road, not the flattest one. Note whether power fades on a long climb, and ask for the rated power, peak power and torque together. Test the same climb more than once, including once after the battery has already done some work, because behaviour on a full battery and behaviour later in the day can differ. Also test slow-speed control: starting on a slope, manoeuvring in a crowded yard, and pulling away smoothly with a load are daily tasks for many riders, and a vehicle that is strong at speed but awkward at walking pace is a poor match for them. Record what load you used in kilograms or in a clear description — "one rider plus passenger" is a record; "quite heavy" is not. If the sample struggles on your steepest regular road, do not accept a promise that production will be stronger. Ask what configuration change would fix it, what that change costs, and whether it changes the battery, documents, or price — in writing.
- Brakes, tyres and handling. Test braking from your normal riding speed, check tyre grip and pressure, and ride over the road surfaces your customers actually use. Brake repeatedly, not once, and from a consistent speed on a safe, empty stretch, noting whether the vehicle stops straight and whether the feel changes as the brakes are used. Ride over your real surfaces — patched tarmac, gravel edges, wet patches after rain where it is safe to do so, speed bumps, and broken kerbs — and listen for rattles and feel for anything that wanders or knocks. Check the tyre size and type against the specification, and ask which tyres production vehicles will carry, because a sample on one tyre and a container on another will not ride the same way. If anything in braking or handling concerns you, treat it as a stop point, not a negotiation point: these are safety items, and they must be right on the sample, not promised for later.
- Lights, horn, dashboard and switches. Check every light, indicator, horn, display and switch — including at night. Small electrical faults are the most common first complaint. Work through them one by one with a helper watching from outside the vehicle: headlight on both settings where fitted, indicators front and rear, brake light under both brakes where applicable, number-plate and tail lights, horn, and every dashboard reading and warning you can trigger. Then ride at night on a road you know, because a headlight that looks bright in a warehouse may light the road poorly, and a dashboard that is clear at noon may glare or wash out after dark. Press every switch with gloves if your customers ride with gloves. Note anything intermittent — a light that flickers over bumps or an indicator that cancels oddly — and record it on video, because intermittent faults are the hardest to prove later from memory alone.
- Build and finish. Look for panel gaps, loose fasteners, paint defects, cable routing and water ingress points. Shake, fold and unfold anything your customers will move every day. Go slowly here, because this check predicts your after-sales workload and your workshop time — and before you order, confirm the warranty terms in writing with the factory, including what the terms cover and for how long. Run your hands along panel edges, check that fasteners are present and tight, look inside the storage areas and under the seat, and follow the cables where you can see them: are they routed away from sharp edges and moving parts, and are connectors seated properly? Operate the stand, the seat latch, mirrors, and any folding or removable parts repeatedly, the way a customer will, hundreds of times over a vehicle's life. After riding in wet conditions or washing the sample carefully, look for water where water should not be. Photograph every defect, however small, and number the photos to match your test sheet, so the factory can find the exact point you mean without a long exchange of messages.
- Spare-parts match. Confirm the controller, charger, battery connector and wear parts on the sample are the same parts the factory will supply for after-sales — and ask for the spare-parts list and prices with the sample. This check connects the sample to the years after the sale. Ask the factory to list, against the sample you tested, the parts a dealer most commonly needs: charger, controller, battery connector, brake parts, tyres, cables, switches, lamps, and mirrors — and to confirm which of them will be available as spares for your configuration. Fit matters as much as availability: ask whether connectors and mounting points on production vehicles will match the sample exactly, so that a spare ordered next year fits a vehicle sold this year. A common and expensive mistake is to negotiate the vehicle price in detail and leave spares as an afterthought, then discover that a cheap vehicle is supported by slow or mismatched parts. Decide before the container order which spares you will stock from day one, based on what this check shows you.
- Packing, as it will arrive. Ask how the sample was packed, and whether production vehicles will be packed the same way. Photograph the carton and the protection inside; this is your evidence if a container arrives damaged. Samples often travel better than bulk shipments, so ask the specific question directly: will production vehicles, in a full container, be packed with the same materials, the same protection on painted and fragile parts, and the same securing inside the carton or frame? Request photos or a short video of a production packing run if one is available, and confirm how batteries and chargers are packed for your shipping form. Unpack the sample as a customer or workshop would, noting whether assembly steps are needed, whether the tools and instructions required are included, and how long a careful first assembly takes. That timing, multiplied across a container, is real workshop cost — better to know it from one sample than from a warehouse full of vehicles waiting to be built.
- Paperwork for the sample. Check that the invoice, packing list and any test or transport documents name the sample's exact model and battery. If the sample's paperwork is wrong, the container's paperwork probably will be too. Treat the sample shipment as a rehearsal for the container shipment. Compare every document against your confirmed sample specification: model name, motor power, battery voltage, capacity and chemistry, quantity, and the description of how the vehicle was shipped. If a document uses a shorter or older model name, or a different battery description, ask for a corrected version and note how quickly and willingly it was corrected — that response tells you a great deal about how a document problem on a full container would be handled. Keep the sample documents with your test sheet, so that when you later check the container's draft documents, you are comparing them against a set you have already verified once.
After the test: decide in writing
Write down what passed, what failed, and what must change before the main order — and send it to the factory. Do not place a container order on a verbal promise to fix a problem. On the Lubon LB-CS, the listed motor is 1500W, with lithium / lead-acid battery options (for example 60V/72V, 32Ah) and a listed top speed of 45 km/h — confirm the rated and peak power, the torque, the tested load and the range test conditions for your exact configuration, and test the sample under your real load, before you order.
Structure that written decision so the factory can act on it without guessing. A simple format works well: first, the configuration you tested, exactly as confirmed; second, the results, check by check, with your measured figures and photo references; third, the changes you require before a main order, each stated as a specific outcome rather than a general wish — not "better brakes" but the exact braking behaviour or part change you are asking the factory to confirm; fourth, the points the factory has confirmed in writing it will meet in production, and the points still open. Send it, ask for a written reply against each numbered point, and keep both documents with your order file. If a required change affects price, battery, documents, or delivery time — the listed delivery time for the LB-CS is 15 days, to be confirmed for your exact order — get the revised figures in writing before you pay a deposit, not after.
It also helps to decide your own walk-away points before emotion and sunk cost build up. Agree internally, while the sample is still being tested, which failures would stop the order entirely — safety items and paperwork mismatches are natural candidates — and which findings would simply change the configuration, the spare-parts stock, or the price negotiation. Buyers who set those lines in advance make calmer decisions than buyers who have already promised the model to their customers.
A sample that fails honestly is a success: it just saved you a container.
Want to test a sample before you order? Tell us your typical load, your steepest roads and your daily mileage, and we will confirm the matching configuration and sample terms before quotation. Email: saravehicle@jxlubon.com · WhatsApp: +86 189 7035 3905
