Don't Judge an Electric Scooter Motor by Its Watts: Load, Hills and Real Power
Two scooters can share the same watt rating and climb very differently. What load, hills and motor type really change for delivery and passenger use.

The number on the brochure is only half the story
"1500W" looks like a simple comparison. Two scooters can carry the same watt rating and behave very differently on a hill with a passenger, or on a delivery run with a loaded box. If you buy for delivery, rental or passenger use, the headline watt figure is the wrong place to stop.
The problem is not that the watt figure is useless. It is that it is incomplete, and it is often not even the same measurement from one brochure to the next. One supplier may be quoting a motor's rated power, another its peak power, and a third may simply repeat the largest number associated with the model. Placed side by side in a spreadsheet, those three numbers look like an honest comparison. On the road, with your load, on your hills, they are not.
This matters most for the buyers who can least afford the mistake. A scooter bought for gentle personal use on flat streets will forgive a modest motor. A scooter bought to earn money — carrying deliveries all day, taking a passenger, working a rental fleet — will expose a weak specification within the first week. The rider will describe it in practical terms, not engineering ones: it will not pull away cleanly with a load, it slows down too much on the bridge or the hill, or it feels strong in the morning and tired later in a long climb. By then the container has arrived, the stock is in your showroom, and the conversation with the factory is much harder than it would have been before you ordered.
So use the watt figure as the start of a set of questions, not as the answer. The rest of this guide sets out those questions: what kind of power figure you are being given, how much torque sits behind it, what the controller allows the motor to do, what load and gradient the scooter was actually tested under, and what all of that does to the battery. None of this requires you to become an engineer. It requires you to refuse to compare scooters on one number, and to test a sample under your own conditions before the main order — the same discipline you would apply to any other working vehicle in your business.
A simple habit helps at the quotation stage. Whenever a supplier gives you a power figure, write next to it three things: rated or peak, measured where, and tested with what load. If any of the three is blank, the figure is not yet usable for a buying decision. Suppliers who know their product can fill in the blanks. Suppliers who cannot are telling you something important about how the number was produced.
Rated power is not peak power — and neither is torque
- Rated (continuous) power is what the motor can sustain. Peak power is what it can deliver briefly. A motor quoted only at peak power will look stronger on paper than it rides in practice.
- Torque is what moves a load from a standstill and up a slope. Two motors with the same watts can deliver different torque, depending on motor type, gearing and controller settings.
- The controller matters as much as the motor. Current limits, acceleration settings and thermal protection decide whether the scooter keeps its power on a long climb or fades after a minute.
Always ask for the rated power, the peak power and the torque figure together — and ask whether the figures are measured at the motor or at the wheel. If a supplier gives you only one number, you do not yet have a comparison.
Consider what each term means for a working day. Rated power is the honest working figure: it describes the output the motor is built to keep delivering, which is what a delivery rider on a long route or a scooter climbing an extended slope actually depends on. Peak power has a legitimate use — pulling away from a standstill, or a short, sharp rise — but it is by definition brief. A buyer who compares one scooter's peak figure against another's rated figure will choose the wrong scooter and will not understand why the "stronger" machine disappoints. Ask for both figures for every model you compare, in the same format, so the comparison is like for like.
Torque deserves the same attention, because for load work it is often the figure the rider actually feels. Watts describe a rate of work; torque describes the turning force that gets a loaded scooter moving and keeps it moving against a slope. That is why the original warning matters: two motors with the same watts can deliver different torque. Motor type, gearing, and controller settings all shape the result, so do not accept an argument that equal watts must mean equal pulling ability. Ask for the torque figure, ask how it was measured, and then — most importantly — treat any paper figure as a claim to be verified on your sample, on your steepest regular road, with your typical load aboard.
The controller is the third part of the system, and the one brochures mention least. The controller decides how much current the motor may draw, how acceleration is delivered, and how the system protects itself when it gets hot. Two scooters with the same motor can therefore behave differently because their controllers are set up differently: one may pull strongly but protect itself early on a long climb, the other may feel gentler at pull-away but hold its pace. Neither set-up is automatically right for you. What is right depends on your use — stop-start delivery work, steady passenger carrying, or hill work — which is why you should ask for the controller's current limit and settings as part of the specification, and confirm them in writing for the exact configuration you are ordering. If a configuration changes — a different battery, a different motor option — ask whether the controller and its settings change with it, and get the answer in writing rather than assuming the set-up carries over.
A common mistake at this stage is to chase a bigger headline number as insurance: if some power is good, more must be safer. That logic fails twice. First, a bigger peak figure may add nothing to sustained climbing. Second, a motor and controller combination that is poorly matched to the battery and the scooter's actual work can waste energy, generate heat, and shorten the useful day. The goal is not the biggest number. The goal is a matched system — motor, controller, and battery specified together, tested together, under a load that resembles yours.
Load and hills: the test conditions that change everything
Real-world load is not one light rider on a flat road. Before you order, think about your actual use:
- Delivery: rider plus a loaded box, stop-start traffic, all day. Daily mileage and the weight of the load matter more than top speed.
- Passenger use: two people, plus the scooter's own weight, on your steepest regular road — not the flattest one.
- Hills and heat: a long climb in hot weather is the hardest test for a motor and controller. A scooter that is fine on flat ground can overheat or slow sharply here.
Ask the factory what load and gradient the scooter was tested at, and whether those figures are in the specification sheet. Then test a sample yourself on your own roads, with your own typical load, before committing to a container.
Turn that advice into a written test profile before you talk to any supplier, because "our area is hilly" and "our riders carry deliveries" are too vague to specify a scooter against. Write down, for your own business: the typical all-up load your scooters will carry — rider, passenger or cargo, and the scooter itself — in the heaviest regular case, not the lightest; the steepest road your riders use regularly, and how long that climb lasts; the pattern of the working day, including how much of it is stop-start and how many hours the scooter is in use; and the conditions, including the heat your scooters will work in. You do not need laboratory precision. You need an honest description of a hard normal day, because that is the day your customers and riders will judge the scooter by.
Then use that profile in two places. First, send it to the factory and ask, in writing, what load and gradient the scooter was tested at and whether those test conditions are in the specification sheet for the exact configuration you are considering. If the factory's test load is far lighter than your profile, or its test route was flat, you have learned that its published figures do not describe your use — which does not automatically disqualify the scooter, but it means your own sample test carries the full weight of the decision. Second, use the same profile as your sample test script. Test the sample on your own roads, with your own typical load, over your steepest regular climb, and record what happens: how it pulls away loaded, how much speed it loses on the climb, whether power fades as the climb continues or the run goes on, and how the scooter feels at the end of a representative working period. Write the results down and keep them with the order file. A recorded test, done before the main order, is what turns a later disagreement about performance into a factual discussion — and it is far cheaper than discovering the same facts with a container in your warehouse.
Be honest in the test, too. Testing with your lightest rider, an empty delivery box, and the easiest route produces a pass that means nothing. Testing with a load slightly above your typical case gives you a margin you will be glad of when a rider takes a heavier job. And repeat the hill test rather than doing it once: a scooter that climbs well once, cool and freshly charged, may behave differently later in a working day, and it is the later behaviour your business will live with.
One more decision criterion belongs here: top speed is rarely the limiting factor for working use. A scooter can reach a respectable speed on the flat, empty, and still be the wrong tool for loaded hill work. Judge the candidates on pull-away, climbing, and sustained pace under load first, and treat speed as a secondary check against your market's needs and rules — confirm any local requirements for your market yourself rather than assuming a listed figure settles them.
Battery and range under load
A heavier load does not just ask more of the motor — it drains the battery faster. The range figure quoted for a single light rider can fall sharply with a passenger or a delivery box. Check the battery capacity in watt-hours (voltage × amp-hours) and ask how range was measured, with what load, before you promise a range to your customers.
The watt-hour check is simple arithmetic you can do on any quotation, and it immediately improves comparisons. A battery described as 60V, 32Ah stores 60 × 32 = 1,920 watt-hours; a 72V, 32Ah battery stores 72 × 32 = 2,304 watt-hours. Two scooters both described loosely as having a "big battery" can therefore differ substantially in stored energy, and a scooter with a nominally similar battery can be offered in more than one configuration. Do the multiplication for every configuration you compare, write the watt-hour figure next to the motor figures in your notes, and ask which of those configurations any quoted range figure belongs to.
Range itself needs the same treatment as power: a range figure without test conditions is not a comparison, it is a headline. Ask how the range was measured — with what load, on what terrain, and as part of what pattern of riding — and get the answer in writing for your exact configuration. Then apply the original warning in your own planning: expect real range under your real load to be lower than a light-rider figure, plan your riders' and customers' use on the basis of your own sample test rather than a brochure number, and do not promise a range to your customers until your sample has covered your own routes with your own load. Promising a brochure range to a delivery business or a passenger customer, and then missing it in daily use, damages your reputation in a way a careful specification discussion never will.
Battery choice also interacts with the motor discussion rather than sitting beside it. The battery options on a model change the energy available to the system and can change how the scooter is configured overall, so confirm the motor, controller, and battery as one package for the configuration you will actually sell — not the motor from one version and the range from another. If you plan to offer two configurations, test and document each one separately, and make sure your sales material keeps their figures separate as well. Mixing figures between configurations is one of the easiest ways an honest dealer ends up misleading a customer.
On the Lubon LB-CS, the listed motor is 1500W, with lithium / lead-acid battery options (for example 60V/72V, 32Ah) and a listed top speed of 45 km/h. Those are the listed figures for that configuration — confirm the rated and peak power, the torque, the tested load and the range test conditions for your exact configuration, and test a sample under your real load, before you order. Note what those listed figures do and do not tell you: they give you a starting point and the battery arithmetic above — 1,920 or 2,304 watt-hours for the 32Ah options — but they do not by themselves tell you the torque, the controller set-up, or the tested load. Those are exactly the items to confirm in writing, which is the work of the final section.
Five questions to put in writing
- Rated power, peak power and torque — all three, with where they are measured.
- Motor type and controller current limit.
- Tested load and gradient, and whether they are in the specification sheet.
- Range test conditions, including rider weight and terrain.
- What a sample test should show: your roads, your load, your steepest hill — recorded, before the main order.
Do not treat these five as a casual email. Make them a specification sheet for your order, answered by the supplier in writing, attached to the order, and checked against the sample when it arrives. A few practical additions make the five questions work harder. Ask the supplier to state the answers for your exact configuration — model, motor, controller, and battery together — and to say explicitly if any answer changes when the battery option changes. Ask whether any figure in the answers is a peak or short-duration figure and how long it can be sustained, so nothing in your own sales material repeats a brief figure as a continuous one. Ask what evidence supports the tested load and gradient figures — a specification sheet entry, a test record — and keep copies in your file. And where anything about after-sales support or warranty is discussed in connection with performance, confirm the terms in writing; do not assume a period or a coverage that was never stated.
Then close the loop with the sample. Agree before the sample is shipped what your test will cover — your roads, your load, your steepest hill, a representative working period, and the range run you will do — and record the results against the written answers, point by point. Where the sample matches the written figures, you have a configuration you can order with confidence. Where it does not, you have a specific, documented question to resolve before any container is discussed. Either way, you have bought on evidence gathered under your conditions, which is the whole point of this guide: watts are where the conversation starts, never where it ends.
You can also reach Lubon Motor at saravehicle@jxlubon.com or on WhatsApp at +86 189 7035 3905. Lubon is a Jiangxi-based company, with its electric two-wheelers produced at the Wuxi base. In your first message, include the test profile described above — your typical and heaviest regular load, your steepest regular road, your daily mileage and working pattern — and ask for the rated power, peak power, torque, controller limit, tested load and gradient, and range test conditions for the configuration recommended for that profile, confirmed in writing before quotation.
